Find Gyproc EasiPatch Plasterboard Patches at your local decorator centres and builders’ merchants. Find the details here . Once the adhesive has dried enough to support the patch you can now push the screw out into the wall void. Leave for a further 24 hours for the adhesive to completely harden off and then you can start filling. Apply the filler by working it into the holes of the patch and towards the edge. Feather out at least 50mm beyond the edges of the patch to create a smooth, seamless finish. Leave to set for a minimum 30 minutes. For larger holes locate the joists either side of the hole in the ceiling and mark the middle with a straight pencil line and create a rectangle around the hole. Cut out and add two noggins to bridge the gap between the joists. Storage & Home Clearance Furniture Clearance Garden & Outdoor Clearance Lighting Clearance Electrical Clearance Tools Clearance Paint & Decorating Clearance Flooring & Tiling Clearance Building & Hardware Clearance Bathrooms & Plumbing Clearance Kitchens Clearance

Use a digital stud detector to locate studs, noggins and joists in walls and ceiling (Image credit: Getty Images) Can I Use Caulk To Fill Holes? Gyproc EasiPatch Plasterboard Patches are coming soon (Available April 2022). The must-have repair solution for damaged plaster and plasterboard is now available in To repair a hole in a hollow door, wall, or ceiling, firstly trim the edges of the hole and make is square. Ironically, you actually have to make the hole larger before you can go about fixing it!Now that you have squared up the hole, the next job is to make a patch. You can either use a scrap piece of plasterboard or timber. Spread a small blob over the hole and wait for it to dry. Once dry, get a 180-220 grit sandpaper and rub down until smooth and blended with the current surface. How do You Fix a Hole in Plasterboard on the Ceiling?

Due to the nature of plasterboard and in a similar way hollow doors, they can become damaged quite easily. Once the patch is dry and firmly in position, gently remove the screw. Use patching plaster, all purpose filler or multi-finish plaster — mix up enough to cover the patch and gently press into the hole and spread with a putty knife that is larger than the hole to help get a smooth finish.Artex Caulker (250mm ) helps to fill joints and create smooth finishes or any suitable jointing knife

Yes you can use decorators' caulk to fill small holes such as nail and screw holes, but it's not really suitable for holes any bigger than quarter of an inch. Add a dollop of caulk and smooth out with a putty knife or a wet finger for nail and screw holes.As you will need to do a bit of cutting, before you start this, firstly run over the area around the hole with a wire detector to make sure there aren’t any wires, pipes or other items that you may accidentally cut through. Cut a piece of plasterboard that is slightly narrower than the hole but an inch or so longer top and bottom. Screw in a long screw in the middle of the patch; this will be used to position the patch in place. When the plaster starts to dry, lightly scratch the surface with the end of the trowel in this pattern. Anybody Can Use It - Apply the plasterboard repair patch kit to your wall or ceiling. Once the mesh has bonded, cover over with plaster and smooth out with a scraper. You can then decorate the wall as preferred to make it look like new. Gyproc EasiFill 20 has a working time of 20 minutes and the second coat can be applied after 40 minutes. Gyproc EasiFill 45 has a working time of 45 minutes and the second coat can be applied after 80 minutes.

Another complication that springs to light when you have unfortunately made a hole in a plasterboard wall or hollow door is the void behind it due to the construction of the stud work used to hold the plasterboard up or provide the framework for the door meaning that you can’t just use filler as there is nothing to bond it to. Depending on the shape of the hole, whether its circular or has jagged edges you may need to use a padsaw, jabsaw or hobby knife. Be careful using any of these items as they are sharp and can slip quite easily. Feed a batten into the hole and twist it so it is either upright or horizontal and one third of the distance either up or down or across the hole. Make sure you have a 50mm overhang either side of the hole.

Remove any loose bits from the edge of the hole or damaged area, and sand this down. Remember to always wear eye protection when sanding. Cut a piece of plasterboard that is the same width but around 25mm longer than the hole. Squeeze on some ‘instant grab’ around the edge of the board and then wind in a long screw to the centre of the repair piece. First remove any loose chunks of plaster use a hammer and chisel if necessary then vacuum out the area to get rid of the dust and debris. Artex Limited is trading as Artex . Registered office - Saint-Gobain House, East Leake, Loughborough, Leicestershire, LE12 6JU.