A variation on the workaround illustrated above. On the left-hand side, a pre-cast concrete edging has been used to create the retainer and the paving is significantly higher than the dpc. A dished channel unit has been used at the base to direct any surface water to the gullies. Although a relatively narrow channel is shown here, these 'dry area' solutions can feature much wider channel, often 600mm or more, and so consideration must be given to safe-guarding the edge to prevent accidental falls. Drained channel arrangement

Please note the following postcodes are classed as Non-Mainland UK or Remote / Rural delivery: AB, IV, KW, PA, PH, HS, KA, ZE, PO30-PO41, IM, JE, GY, BT, TR21-TR25. The reveal should be protected throughout its width by a continuous DPC. The width of the DPC should be sufficient to be fixed to, or overlap, the frame and fully protect the reveal. For very severe exposure conditions, rebated reveal construction or a proprietary closer, suitable for the conditions, should be used. If renovating after a pre-existing damp problem, consider installing fresh sawn & carcassing timber to replace rotten stud work and battens. This DPC is suitable for masonry walls and has a diamond embossed surface to offer better mortar adhesion.The Building Regulations require at least 150mm between the dpc and the ground or any paving. This is what is known as 'Best Practice'. However, there are situations where it is just not possible, or practical, to maintain this regulation. On professional work, and new build projects, every possible effort should be made to ensure the 150mm rule is not breached, but, for small, domestic projects, such as a driveway or patio, there are cases where keeping the paving to 150mm below dpc would involve a huge amount of work that cannot be justified. In such cases, the 150mm rule can be 'bent' a little, but with the following provisos... Installation should be according to the code of practice CP102:1973 and normal DPC good practice procedures set in BS 5628 should be followed. DPC installation is simplest in the new construction process. For external walls, the DPC should be applied 150mm above the external ground level. You need to ensure it is linked with the DPM in solid floors. Damp proofing membranes protect different parts of a structure from damage arising from damp, including mould and mildew, and the risk of rotten timber.

Just solid masonry separated by a vertical DPC. This means that this part of the wall will be colder that the rest of the wall, resulting in condensation forming around this part of the structure – a case of ‘cold bridging’. Judging by the standards of workmanship, it’s quite likely that there is no insulation below the DPC either, meaning the same problems will happen around the skirting too. It’s important to think about cold bridging through any part of the structure but especially where junctions occur. Further information If you are looking for a premium quality, DPC to be used in your construction – this is product is perfect. Our metalwork wall & frame ties are ideal for work on cavity walls, to hold everything securely together once your damp course is in place. A DPC should be provided a minimum 150mm above adjoining surfaces and linked with the DPM in solid floors. The polyethylene foam insulation used in ARC Insulated DPC has a thermal conductivity of 0.039W/mK.The Visqueen Polyethylene Damp Proof Course is made to the minimum damp proof course standard set by the British Standard, offering you a more cost effective but still trade suitable option.

DPC (Damp proof course) is used when a physical barrier is required to prevent moisture travelling up building walls. Most existing constructions should have a form of DPC already in situation, however this product will be required for new wall constructions to prevent an issues with rising damp.The paving/ground level should always be at least 75mm below the DPC. Anything less than that is just asking for trouble.* Jewson building materials can make sure you have everything you need to not only install a damp proof course, but to complete the job from start to finish. The DPC membrane should be applied to a fresh bed of mortar. Make sure that the area is completely free of anything that may puncture the DPC or prevent it from lying flat.