The maximum distance between vehicles and ground must take account of the nature of the installation, the type of vehicles and the rescue procedures. In the case of open cars it must also take account of the risk of fall as well as the psychological aspects associated with the distance between vehicles and ground. Where a subsystem with an EC declaration of conformity is found not to comply, the competent Member State shall take appropriate action against whomsoever drew up the EC declaration of conformity and shall so inform the Commission and the other Member States. It is not necessary to require all existing cableway installations to be brought into conformity with the provisions applicable to new installations. However, this may prove necessary if the essential safety objectives are not complied with. In that event, the Commission should propose to the Member States a series of recommendations designed to ensure that existing cableway installations on their territory afford users a high degree of protection in the light of the provisions applicable in this field to new installations. It must notify its decision to the manufacturer. The notification shall contain the conclusions of the examination and the reasoned assessment decision.

Over my experiences of running in ASICS I have come to expect a balanced feeling when it comes to cushioning. This was not the case with the GT 2000 9. It was surprisingly firm. The notified body shall draw up the EC examination certificate in accordance with Annex VII and the technical documentation which accompanies it. The technical documentation must include all the necessary documents concerning the characteristics of the subsystem and, where appropriate, all the documents certifying the conformity of the safety components. It must also contain all the relevant details of the conditions of, and restrictions on, use and of the instructions for servicing.On the basis of the provisions referred to in paragraph 1, Member States may not prohibit, restrict or hinder the free movement of safety components and subsystems referred to in Annex I which are accompanied by an EC declaration of conformity within the meaning of Article 7 or Article 10. It is fair to say I have a soft spot for them, but it has been years since I have run in them. How does the GT 2000 version 9 hold up to those of yesteryear? Member States shall take all necessary measures to ensure that subsystems within the meaning of Annex I are placed on the market only if they permit the construction of installations complying with the essential requirements referred to in Article 3(1). define and state the precautions which should be taken to avoid the risks which it has not been possible to eliminate completely by means of the provisions and measures referred to in the first and second indents. The control devices must be designed and constructed so as to be safe and reliable, to withstand normal operating stresses and external factors such as humidity, extreme temperatures or electromagnetic interference and so as not to cause dangerous situations, even in the event of operational error.

The notified body must periodically carry out audits to make sure that the manufacturer maintains and applies the quality system and shall provide an audit report to the manufacturer. This Annex applies to the safety components referred to in Article 1(5) of this Directive with a view to establishing their compliance with the essential requirements which concern them referred to in Article 3(1) of the Directive and defined in Annex II. This module describes that part of the procedure by which a notified body ascertains and attests that a specimen, representative of the production envisaged, meets the provisions of this Directive.The only downside I experienced was that once my feet got really wet when running in the rain or on wet surfaces, my feet generally stayed pretty wet. Conclusion The notified body must affix, or cause to be affixed, its identification number on the approved component and shall draw up a certificate of conformity concerning the tests carried out. Each Member State shall lay down procedures for authorising the construction and the putting into service of installations which are located within its territory.

At the request of the main contractor or his authorised representative, all planned installations shall be subject to a safety analysis as defined in Annex III which covers all safety aspects of the system and its surroundings in the context of the design, realisation and putting into service and makes it possible to identify from past experience risks liable to occur during operation. The manufacturer must allow the notified body entrance for inspection purposes to the places of manufacture, inspection and testing, and storage, and must provide it with all necessary information, in particular: The manufacturer or his authorised representative must keep the notified body that has approved the quality system informed of any intended updating of the quality system.

SUITED FOR:

The auditing team must have at least one member experienced as an assessor in the product technology concerned. The evaluation procedure shall include an assessment visit to the manufacturer's premises. descriptions and explanations necessary for the understanding of the said drawings and schemes and the operation of the product,

Those technical specifications which are also required to supplement European specifications or other standards must not jeopardise compliance with the essential requirements referred to in Article 3(1). In the event that important characteristics, subsystems or safety components of existing installations undergo modifications for which a new authorisation for entry into service is required by the Member State in question, such modifications and their repercussions on the installation as a whole must satisfy the essential requirements referred to in Article 3(1). The last thing a runner wants is for the shoe to feel like it is weighing them down, and the GT 2000 9 not only refrains from such a feeling but rather provides a bit of an extra bounce in the step! The ASICS GT 2000 9 offers long-lasting durabilityThe EC procedure for examining subsystems shall be carried out at the request of the manufacturer or his authorised representative established in the Community or, in their absence, any natural or legal person who places the subsystem in question on the market, by the notified body referred to in Article 16 which the manufacturer or his authorised representative or the abovementioned person appointed for that purpose. The EC declaration of conformity shall be drawn up by the manufacturer or his authorised representative or the abovementioned person on the basis of the EC examination in accordance with Annex VII. The notified body must examine the component and must carry out the appropriate tests as set out in the relevant European specifications referred to in Article 2(2) of this Directive, or equivalent tests, to ensure its conformity with the relevant requirements of this Directive. For the purposes of this Directive, a harmonised standard is a technical specification (European standard or harmonisation document) adopted by one or other of those bodies, or by both, at the request of the Commission pursuant to Directive 98/34/EC of the European Parliament and of the Council of 22 June 1998 laying down a procedure for the provision of information in the field of technical standards and regulations and of rules on information society services(6) and in accordance with the general guidelines referred to above. In relation to standardisation, the Commission should be assisted by the committee referred to in that Directive, which will, if necessary, consult technical experts.